|
|
|
|
|---|
Complete flipper assembly for newer model Williams pinballs. Have one set of gold plated end of stroke switch contacts. Ref #15849
Complete flipper assembly for older model Williams pinballs. Have one set of heavy duty end of stroke switch contacts with capacitor.
Complete flippers rebuild kit for older model Williams pinballs before 1992. Complete kit contains main parts for two flippers associated with flipper assembly failure. Williams Ref #A13524-1
Complete flippers rebuild kit for newer model Williams pinballs after Terminator II pinball. Complete kit contains main parts for two flippers associated with flipper assembly failure. Williams Ref #A13524-8
This new Williams flipper opto board is a plug in replacement complete with sensors. Williams reference #A17316.
Pinball optocoupler for flipper boards on Williams pinball machines. This is a 5 legged opto used on board above, Reference number 5490-14575-00.
Flipper cap and shaft for Data East/ Sega/ and Newer Stern games. Can also be a substitute for newer Bally / Williams Games. Sold individually.
Replacement 3 inch flipper cap used on older Atari, Bally, Chicago Coin, and Stern games from the mid 1970's-1980's. Sold individually.
2 inch flat top white flipper plastics with screw hole used in Gottlieb games from the Late 1960's-1990's. Sold individually.
Replacement 3 inch flipper cap used on early Gottlieb Games from mid 1970's-Late 1980's. Uses narrower 3/8" width flipper rings. Sold individually.
Replacement white Gottlieb flipper cap and shaft for all Gottlieb pinballs after 1991. Sold individually.
2” Round top with blue lettering flipper plastic caps with screw hole. Has blue "FLIPPER" lettering. Used in games from the 1940's-1980's. Sold only in pairs.
2” Round top white flipper plastic caps with raised blue "FLIPPER" lettering and without screw hole. Used in Bally, Chicago Coin, Stern, and Williams games from the 1960's-1980's. Sold only in pairs.
2” Flat top white flipper plastic caps with screw hole. Has outline and "FLIPPER" lettering in blue. Used in Gottlieb games from the late 1960's-1970's. Sold only in pairs.
Left side banana flipper rubber cover only. Only a few left. Right side are not available.
Flipper bushings for Williams and Bally pinballs.
Bushings for Data East machines.
Bushings for Series 80 and newer Gottlieb machines. Fits 6mm shafts.
New style link for all machines after 1992 that connects the plunger and flipper together. Ref # 03-8753
Older style link for all Bally and Williams machines manufactured before 1992.
Small bushing that always falls out and gets lost when changing link. Used with two links above.
Old style link for all machines that connects the plunger and flipper together. Fits most mechanical and early electronic pinballs.
Link used on Williams machines.
Plunger with twin fiber links used on Williams machines. Ref# A8335
New style flipper plunger and link assembly for Williams, Bally and Data East. Reference #A15847
Old style flipper plunger and link assembly for Williams, Bally and Data East. Reference #A10656
Williams ringed plunger and link Williams ref #3A8085 - 2A2364. Plunger is 2 1/8" long with 1/4" hole in link.
Williams plunger and link Williams ref # A5103 - A8050-1. Plunger is 2" long with 1/4" hole in link.
Plunger and link for late model Premier and early other electronic and mechanical pinballs. 2 inch long plunger with 5mm hole in link.
Bally flipper plunger and link for early electronic pinballs. Plunger is 1 15/16" long with 5mm hole in link. Ref # A-3714-1
Plunger ready to accept your choice of link. 2 inches long.
Crank used on all Williams machines. Williams ref # 1A8073-L/R. Available in right or left sides.
Plastic protective sleeve used on crank arms to minimize wear on end of stroke switches. Can be heat shrunk onto the crank arm.
Right & Left (as seen from the front or playing position) newer style plunger, link and crank assembly for Williams and Bally machines 1992 and newer.
Right & Left (as seen from the front or playing position) older style plunger, link and crank assembly for Williams and Bally machines manufactured before 1992.
Return spring for most all Williams, Bally and Data East.
Return spring for Williams machines. Williams ref number 10-364.
Williams mounting plate. Williams ref # C8231-L/R , C9954-L/R, C11627-L/R, B13104-L/R. Available in right or left sides.
Williams coil mounting bracket. Ref # 01-7695.
New Williams backstops. 22mm between mounting holes, fits newer Williams.
New Data East coil backstops. 22mm between mounting holes with large 6mm mounting holes. Heavy duty coil stop.
New Bally backstops, 15mm between mounting holes.
New Bally copper backstops, 15mm between mounting holes.
New Gottlieb backstop, 20mm between mounting holes, for electronic machines.
New universal stop made to replace worn stops on your old stop bracket. Easy bolt on installation.
Data East assembly for older machines. Can be used on the right or left.
Gottlieb early electronic crank assembly. Fits Star Series 80 models.
Gottlieb flipper lever arm for all models after 1991. Available in right or left sides.
Gottlieb return spring.
Bally Flipper plungers for 1989 and earlier machines.
Bally lever arm for 1989 and earlier machines. Used with plunger above.
Heavy duty flipper button switch for electromechanical and Williams, Gottlieb and Bally electronic machines.
Dual flipper control switch that controls upper and lower flippers. Used on flipper buttons and as end of stroke switches on some 4 flipper machines.
Heavy duty end of stroke switches for electromechanical and older Williams, Gottlieb and Bally electronic machines. Heavy duty contact points for carrying high current. Switch blade length is 1 1/2". Reference #03-7811
Heavy duty end of stroke switches for Sega, Data East and others that require a longer blade end of stroke switch. Heavy duty contact points for carrying high current. Switch blade length is 1 7/8". Reference #180-5018-00
Gold end of stroke switches for newer Williams electronic machines, those after Terminator II. Switch blade length is 1 1/2". Reference #SW-1A-194
Bally unit switch. Used on earlier model bally electronic machines. Bally ref number ASW-A20-23.
Stern and Sega flipper end of stroke switch ref #180-5124-00.
Flipper end of stroke switches for Gottlieb early electronic and Bally electronic machines. Heavy duty contact points for carrying high current. Gottlieb ref number GTB-B16363, Bally ref number ASW-A20-34
Filter capacitor for older games that reduces wear and burning on end of stroke switches.
Short 1 1/8" control buttons used on most games with metal control panels.
Locking nut used on the above buttons.
Used control button spring used on control buttons above.
Good used button switch holder used on the above buttons that attaches by the button to under side of control panel. Includes switch and holder. Available in 5/8" width for metal control panels.
lakeside@moneymachines.com
Lakeside Distributors
We accept secure online credit card payments via Verisign Payment Services