|
|
|
|
 
|
|
|---|
| Pinball Parts Home | Arcade Games & Pinballs | Game Room Equipment & Accessories | Pinball Moving Dolly |
Pinball connectors and machine fuses we have for sale replace burned out connectors and fuses used in pinball machines. We carry a large selection of pinball molex connectors, headers, wire terminal connectors and fuses. One of the most common problems with electronic pinball machines is to have burned out connectors and terminals. This causes electrical supplies to be interupted or intermittent. Most of these burned connectors can be seen visually if carefully inspected. So replace all visibly burned connectors and pins.
When replacing pinball fuses, alway make sure that you replace each fuse with the correct amp value fuse. When you are working on a new or unfamilar pinball, you must check in the owners manual to know for sure if the fuse in the machine is the correct one. Many pinball owners do not pay attention to this and replace fuses with higher or wrong value fuses. Replacing fuses with a higher value makes the chances of burning up expensive electronic components very likely. Fuses are used to protect expensive components and attention should be given to replacing them correctly.
.100" 10 position male connector. Can be cut for smaller sections or combined for larger positions.
.100" 36 position male header pinball connector. Can be cut for smaller sections or combined for larger positions.
Bag of 50 .100" crimp terminals.
12 pin connector housing accepts .100" crimp pins.
25 pin connector housing accepts .100" crimp pins.
.156" 10 position male header. Can be cut for smaller sections or combined for larger positions.
.156" 24 position male header. Can be cut for smaller sections or combined for larger positions.
Bag of 50 .156" crimp terminal pins.
2 pin molex KK type housing accepts .156" crimp pins. 3.96mm/.156
3 pin molex KK type housing accepts .156" crimp pins. 3.96mm/.156
4 pin molex KK type housing accepts .156" crimp pins. 3.96mm/.156
5 pin molex KK type housing accepts .156" crimp pins. 3.96mm/.156
6 pin molex KK type housing accepts .156" crimp pins. 3.96mm/.156
7 pin molex KK type housing accepts .156" crimp pins. 3.96mm/.156
8 pin molex KK type housing accepts .156" crimp pins. 3.96mm/.156
9 pin molex KK type housing accepts .156" crimp pins. 3.96mm/.156
10 pin molex KK type housing accepts .156" crimp pins. 3.96mm/.156
12 pin molex KK type housing accepts .156" crimp pins. 3.96mm/.156
14 pin molex KK type housing accepts .156" crimp pins. 3.96mm/.156
15 pin molex KK type housing accepts .156" crimp pins. 3.96mm/.156
Replacement fuse holder has screw hole for easy mounting. 1/4" lugs for easy wire attachment.
Replacement fuse clip used in many arcade and pinball machines. This clip solders into two small holes in a PC board. Fuse Clip is 1/4 in wide; Snap Mount; 15 A (Max.) Two required to make up one fuse holder.
Quantity of 5 AGC Fast Blowing Fuses
Quantity of 5 MDL Slow Blowing Fuses
8AG series fuses are shorter in length than standard fuses and measure 1" long. 6MA series fuses are shorter in length than standard fuses and are 3/4" long.
Blow Off contact cleaner spray. 11 ounce bottle used to clean, degrease printed circuit boards, tape drives, tuners and other precision instruments. Dries quickly, leaves no residue and is safe on plastics.
We accept secure online credit card payments via PayPal Payment Services
|
Lakeside Distributors
310 Covington St. P.O. Box 176 Madisonville, Louisiana 70447 Call Toll Free (866)735-7146 Local(985)845-7146 Voice/Fax (985)845-0570 lakeside@moneymachines.com |
|
|---|